
- Home
- Backsplash Installation
Backsplash Installation in Manteca
The tile between the counter and the upper cabinets, laid out so the grout lines meet the cabinet edges and the range sits centered.
When is the backsplash installed during a remodel?
After the countertops are set and before the final plumbing and electrical trim. The tile runs from the countertop to the bottom of the upper cabinets, set in thinset mortar with grout lines aligned to the cabinet edges and outlets. You can use the counter within 24 hours; grout reaches full strength at 72 hours and is sealed once cured.
- Counter use
- Within 24 hours
- Grout full strength
- 72 hours, then sealed
- Tile
- Ceramic, porcelain, mosaic, glass
- Offered
- Within a remodel only
Protection for the wall, and the detail that ties the room together
A backsplash protects the drywall from water, grease and food splatter, and it is usually the one place in the kitchen where color, texture or pattern carries the design. You arrange it when the countertops, cabinets or layout are already being replaced, so the tile is chosen to match the new materials.
The wall is measured, the tile is selected and each piece is set with thinset in a layout that lines up with the cabinet edges and the outlets. Grout goes in after the adhesive cures and is sealed against staining. From then on you wipe tile clean instead of scrubbing painted drywall.


Center the pattern, and the whole wall looks planned
Pick a pattern, then flip the switch to see what happens when tile is started from a corner instead of centered on the range.
Subway tile laid in a brick pattern creates clean horizontal lines.
A diagonal layout turns the same square tile into a pattern, like the green backsplash in our gallery.
Smaller mosaic sheets add texture and detail, and are cut cleanly around outlets.
Henle aligns grout lines with the cabinet edges and centers the pattern on focal points like the range or sink, so cuts fall at the ends where they are least visible.
Tristan expertly installed my gorgeous tile backsplash, too. I couldn’t be happier!
Cut clean around outlets, finished at every edge
Tile is cut around outlets and window sills with a wet saw, and exposed edges get finished trim or bullnose caps so no raw tile edge is left showing. Outlet covers sit flush on the tile so switches and receptacles mount flat against the wall without gaps.
Tile height is measured before installation to make sure coverage runs all the way from the countertop to the cabinets. Partial rows are avoided by adjusting the starting row or using trim pieces at the top edge.


What this service covers
Included
- Wall measurement and layout
- Ceramic, porcelain, glass and mosaic tile
- Thinset setting, grout and sealer
- Cuts around outlets and window sills
- Bullnose and trim edges
Not included: Backsplash work on its own, outside a remodel.
Backsplash specs from Henle's job files
How backsplashes are written up in Henle's kitchen estimates.
Old tile removed cleanly
Existing backsplash removed and the drywall behind it repaired before new tile.
Your tile or ours
Customer provided or contractor reimbursed tile, installed and grouted.
Subway to the cabinets
3" x 6" subway tile run from the counter to the bottom of the upper cabinets.
Outlets replaced
Backsplash outlets and switches swapped for new devices as the tile goes in.
Under-cabinet LED
LED under-cabinet lighting added on a switch so the new tile is lit.
After the counters
Tile goes in after the counters are set, so the first row sits on a finished surface.
Every Henle estimate lists what is included line by line. Anything not listed is extra and is estimated before it is done.
Backsplash Installation questions from Manteca homeowners
Answers from Henle Construction. Have a question that is not here? Call Tom at (209) 914-1269.
What tile works best behind a stove?
Ceramic and porcelain handle heat and grease without discoloring and clean easily with standard kitchen cleaners, which makes them well suited to the wall behind a cooktop or range.
How soon can I use the kitchen after the backsplash goes in?
You can use the counter and sink within twenty-four hours. Grout reaches full strength after seventy-two hours, and sealer is applied once curing is complete.
Why should the backsplash layout match the cabinets?
Aligning grout lines with cabinet edges and centering the pattern on focal points like the range or sink keeps the installation from looking crooked or unplanned.
How is tile installed around electrical outlets?
Tile is cut to fit around the outlet boxes with a wet saw or nippers, and the outlet covers are installed over the tile so the plate sits flush and hides every cut edge.
What if the tile does not reach the upper cabinets evenly?
The height is measured before installation starts, and partial rows are avoided by adjusting the starting row or using trim pieces at the top edge.
Often part of the same project
Ready to plan your remodel?
Call Tom directly or send a few details about your project. Estimates are free, and what is on the estimate is the only thing that will be done.



